View CSALF8M00T55-B0_7427196.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 1 / 12 { specification of piezoel ectric ceramic resonator CSALF8M00T55-B0 Q date may 19, 2006 J approved by _J checked by issued by 1. m scope {?????`??k????? k ( ? ? ) ??????????????Bj this product specification is applied to the piezoelectric ceramic resonator used for time base oscillator of a microcomputer. please contact us before using any of the products in the appli- cations not described above. 2. ? FvB part number 2-1 ? : CSALF8M00T55-B0 murata part number 2-2 F@? : customer's part number 2-3 F? : customer's drawing number 3. Q appearance and dimensions 3-1 Q : ??????Re???A?? appearance : no illegible marki ng. no visible dirt. 3-2 ?? : 1 ??? dimensions : see figure 1. 3-3 : ?O???????? ? construction : leads are soldered on inside electrode and outer body is molded by resin.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 2 / 12 4. ?? electrical characteristics ?? item ? specification 4-1 ?k? nominal oscillating frequency 8.000mhz 4-2 k?S? initial tolerance 0.50% 0.50% max. 4-3 ? resonant impedance 25 25 max 4-4 ~F? insulation resistance 500m (d.c.10v ??r ) 500m ? min. (applied d.c. 10v) 4-5 ?R withstanding voltage d.c. 100v, 5 d.c. 100v, 5 seconds max. 4-6 ?R rated working voltage (1) ??R d.c. voltage (2) ? a.c. voltage d.c. 6v 15vp-p. 4-7 k?? frequency shift by temperature (-20 +80 ??? ) (-20c to +80c) ??? operating temperature range ?? storage temperature range 0.5% ?? 0.5%max. (from initial value) -20 +80 -20c to +80c -55 +85 -55c to +85c 4-8 U ( k?? +25c 60%r.h.,10 g ) secular change (oscillation frequency for 10 years at 25c 60%r.h.) 0.5% ?? 0.5%max. (from initial value)
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 3 / 12 5. C physical characteristics ? item ? Y test condition ?Y? specification after test 5-1 n random drop 1.0m ????? 3 ? y? components shall be measured after 3 times random dropping on the concrete floor from the height of 1.0m. Q?? 1 4-3 ? no visible damage and the measured values shall meet table 1 and 4-3. 5-2 vibration resistance ? 10 55hz ? 1.5mm ? x,y,z 3 ? 2 rg?y? applying the vibration of amplitude 1.5mm and vibration frequency 10 to 55hz in each of 3 perpendicular directions for 2 hours. 1 4-3 ? the measured values shall meet table 1 and 4-3. 5-3 ?? resistance to soldering heat (1) +260 5 c ????? 1.5 mm ?? 10 1.0 g? ? 1 rg?y? (2) `??? +350 5 c 3.0 0.5 g?? 1 rg?y ? (1)lead terminals are immersed up to 1.5mm from components body in soldering bath of +260 5 c for 10 1.0seconds, and then components shall be left in natural condition for 1 hour. (2)lead terminal is directly contacted with the tip of soldering iron of +350 5 c for 3.0 0.5 seconds, and then components shall be left in natural condition for 1 hour. 1 4-3 ? the measured values shall meet table 1 and 4-3. 5-4 ? solderability lf ? (sn-3ag-0.5cu pct ???? +105 c ? 100%r.h. ? ? 4 rg ` ??? ` ? 5 ? +245 5 c ?? 3 0.5 g lf solder (sn-3ag-0.5cu after being kept in pressure cooker at +105 c temperature and 100%r.h. for 4 hours, terminals of components shall be immersed in a soldering bath at temperature of +245 5 c for 3 0.5 seconds after being placed in a rosin- methanol for 5 seconds. ? 90% ??? ? the solder shall coat at least 90% of the surface of terminal.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 4 / 12 terminal strength terminal pulling ? S 9.8n 10 g? ? force of 9.8n is applied to each lead in axial direction for 10 seconds. ? i ? 1 4-3 ?? no visible damage and the measured values shall meet table 1 and 4-3. 5-5 terminal bending ? 2mm 90 b ? 90 b ? ? ?s 3 ? after lead terminals shall be fixed at 2mm from resonator's body, they shall be folded up to 90 from their axial direction and folded back to -90, then folded back to their axial direction. the speed of fold shall be 3 seconds each. ? ? ? no cutting off. 5-6 ? washability 2 ?? see table 2. Q?? 1 4-3 ? no visible damage and the measured values shall meet table 1 and 4-3.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 5 / 12 6. environmental characteristics ? item ? Y test condition ?Y? specification after test 6-1 dry heat (storage) ? +85 2 1000 rg ?? 1 rg?y? components shall be left in a chamber (temperature: +852c) for 1000 hours, then measured after leaving in natural condition for 1 hour. 1 4-3 ? the measured values shall meet table 1 and 4-3. 6-2 cold (storage) ? -55 2 1000 rg ? 1 rg y? components shall be left in a chamber (temperature: -552 c) for 1000 hours, then measured after leaving in natural condition for 1 hour. 1 4-3 ? the measured values shall meet table 1 and 4-3. 6-3 ? humidity ? +60 2 ? 90 + ? 5 0 %r.h. ? ? 1000 rg ?? 1 rg?y? components shall be left in a chamber (90 to 95%r.h. at +602c) 1000 hours, then measured after leaving in natural condition for 1 hour. 1 4-3 ? the measured values shall meet table 1 and 4-3. 6-4 n thermal shock ? -55 c 30 g ?? +85 c ? 30 g ? 1 ? 10 ? 1 rg?y ? after performing 10 cycles of thermal test (- 55c 30 minutes to +85c 30 minutes), components shall be left in natural condition for 1 hour. 1 4-3 ? the measured values shall meet table 1 and 4-3. 6-5 c?F salt mist test ? +35 2 ? 5 1 48 r gB AF ?? 1 rg y ? components shall be left in a chamber with +352c, density of 51% (by weight) for 48 hours, then measured after leaving in natural condition for 1 hour ??? ? 1 4-3 ?? there shall be no evidence of destructive corrosion and the measured values shall meet table 1 and 4-3.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 6 / 12 6-6 sulfuration 1000ppm 24 rg ? 1 rg y? components shall be left in a chamber with sulfur density of 1000ppm for 24 hours, then measured after leaving in natural condition for 1 hour. ? ??? 1 4-3 ? no breakdown and the measured values shall meet table 1 and 4-3. 1 table 1. ? item ?Y? specification after test k? oscillating frequency 0.3% ??? 0.3%max. (from initial value)
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 7 / 12 7. y test circuit 7-1 k? : 2 ?? oscillating frequency : see figure 2. 7-2 : ??? ?? ?? ? equivalent circuit constants : vector impedance analyzer hp4194a or equivalent. 7-3 y : ? +25 3 ? 60 10%r.h. ? y? B x ??? +5 +35 ? 45 85%r.h. ?y? measuring condition : standard conditi ons for the measurement shall be +253c temperature and 60 10%r.h. humidity. the measurement shall be performed at the temperature of +5 to 35c and the humidity of 45 to 85%r.h. unless otherwise the result is doubtful. 8. ?? packaging standard ? g u? 500 ?? ?????? each minimum package unit of products (500 p cs) shall be in a carton box and it shall be clearly marked with part number, quantity and outgoing inspection number.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 8 / 12 9. ! ? cautions 9-1 ? limitation of applications u???? ?` ? ?b ?? ? m ? ? ???? ? ??? ? ??? Bj ? C C ? C k C ? C ? C ( ? ? ? ) ?? ??C ? C I C ? ? C ? ?C please contact us before using our products fo r the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party ? s life, body or property. aircraft equipment aerospace equipment undersea equipment power plant control equipment medical equipment transportation equipment(vehicles, trains, ships, etc.) traffic signal equipment disaster prevention / crime prevention equipment data-processing equipment applications of similar complexity and/or wi th reliability requirements to the applications listed in the above 9-2 ? `?` C?? fail-safe u? ? ? ? ? ?? ?m ? `?` C? ? ? be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 9 / 12 10. ?? ? caution for use 10-1 ??n????? ? ? ?? Q ? ? the component may be damaged if excess mechanical stress is applied. 10-2 ? H u? ?BC ? ? ? please do not apply excess mechanical stress to the component and terminals at soldering. 10-3 ???? ? ?? _J?? conformal coating of the component is accept able. however, the re sin material, curing temperature, and other process conditions s hould be evaluated to confirm stable electrical characteristics are maintained. 10-4 ? ?k??k ?k????k ?? k ??? _J?? irregular or stop oscillation may o ccur under unmatched circuit conditions.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 10 / 12 11. ! note: 11-1 ?? H ???Fu? g ??? B ?u please make sure that your product has been evaluat ed in view of your specifications with our product being mounted to your product. 11-2 u???{? ?d ? ??? you are requested not to use our product dev iating from this product specification. 11-3 ?{?F I ? ? ?? 1 ? ? ?? ? ?? ?{? ? ?? ? ??{?? r I ? ? ? please return one duplicate of this product s pecification to us with your signature to acknowledge your receipt . in case of no return within three months from submission date, or if we receive order before the duplicate is re turned, this product specification will be deemed to have been received by you. 11-4 ?? gY ??? v s ? ?d ? m ??? ? ?? F\ ? gY ?? | ^ I ?? ? v ?d ?? ??d o ? ??? ???e?? s ? ? ? we consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents. therefore, if your technical documents as above include such terms and conditions such as warranty clause, product liability clause, or intellectual pr operty infringement liability clause, they will be deemed to be invalid.
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 11 / 12 1 ? figure 1. dimensions (CSALF8M00T55-B0) w : 10.0max. ? h : 10.0max. t : 5.0max. : vender's code : u? eiaj monthly code g :mm in mm 2 k?y figure 2. test circuit ceralock ? : CSALF8M00T55-B0 ic:1/6 cd4069ube x2 (rca) vdd:12 0.1v cl1:30pf 1% cl2:30pf 1% rf:1m 0.3 0.1 w 1.3 0.1 0.5 0.1 0.5 0.1 h 5.0 1.0 5.0 0.3 t 800 vdd cl1 cl2 ???`? ceralock (to frequency counter) output rf r
? drawing no. jgc40-3562 ?\?u murata manufacturing co.,ltd. p. 12 / 12 2 table 2 ? washability ?? cleaning solvent ? item ?? ? (hcfc) ipa ? ?????? 750h ?????? ? ? 100s ????? frw hcfc, isopropanol, tap water, demineralized water cleanthrough750h, pine alpha 100s , techno care frw ? condition (1) ? ultrasonic wash ? +60 ??? ? 28khz 20w/l ? 1 1 minute max. in above solvent at +60c max. (frequency : 28khz, output : 20w/l) (2) n ? immersion wash ? +60 ??? 5 n ? 5 minutes max. in above solvent at +60c max. (3) ???? ? ? ? shower or rinse wash ? +60 ??? 5 Q ? ? ` ? 5 minutes max. in above solvent at +60c max. (4) ? drying +80 ` ` 1 5 g ? ? 5 minutes max. by air blow at +80c max. ? notice: 1. ?? ? n ??u??? ? _J ? in case of immersing in cleaning solvent, the temperature of component must be returned to room temperature after soldering. 2. ? L rg ? ? ? ????` 10 ?? total washing time should be within 10 minutes. 3. g ?? B ? ?k? ? ? u ? please insure the component is thoroughly evaluated in your application circuit. 4. c ? ? ?? ? ? ? ? ? ? ?k? ???? the component may be damaged if it is washed with chlorine, petroleum or alkali cleaning solvent.
u? ??k?? ? part name mhz band ceramic resonator ( mhz ceralock ? ) 1. u? ????? ????? 1. product storage condition please store the products in room where the temperature / humidity is stable. and avoid such places where there are large temperature changes. please store the products under the following conditions : temperature : - 10 to + 40 humidity : 15 to 85 r. h. 2. u? u??_y_?B??{? g?{????? ???????_J?? 2. expire date on storage expire date (shelf life) of the products is 6 months after delivery under the conditions of a sealed and an unopened package. please use the products within 6 months after delivery. if you store the products for a long time (more than 6 months), use carefully because the products may be degraded in the solderability and/or rusty. please confirm solderability and characteristics for the products regularly. 3. u??? (1). ???cC???? ????????? ???? ?????? (2). ??m??????????? ? (3) . ??????????? (4). _y_?L?????r? ?? ?????? _ y_???? 3. notice on product storage (1) please do not store the products in a chemical atmosphere (acids, alkali, bases, organic gas, sulfides and so on), because the characteristics may be reduced in quality, and/or be degraded in the solderability due to the storage in a chemical atmosphere. (2) please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. (3) please do not store the products in the places such as: in a damp heated place, in a place where direct sunlight comes in, in place applying vibrations. (4) please use the products immediately after the package is opened, because the characteristics may be reduced in quality, and/or be degraded in the solderability due to storage under the poor condition. 4. ??H????e? ??? 4. others please be sure to consult with our sales representative or engineer whenever and prior to using the products. ? u murata manufacturing co., ltd. ref. no. :pps30mr-001b issue date. :aug. 23, 2005 u??? notice on product storage

▲Up To Search▲

Price & Availability of CSALF8M00T55-B0

	To Download CSALF8M00T55-B0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .